Worst and Best Way to Sight a Rifle!

New Section

In this section, the speaker introduces the topic of zeroing a scoped rifle and mentions the common request for a refresher on this process.

How Not to Zero a Rifle

• The speaker demonstrates a common mistake when zeroing a rifle, which is going to the range without bore sighting.

• Bore sighting at 25 yards is recommended to align the scope with the bore.

• Using a lead sled can help hold the rifle steady during zeroing.

New Section

In this section, the speaker explains why bore sighting is important before shooting at longer distances.

Importance of Bore Sighting

• Shooting at 100 yards without bore sighting can result in wasted ammunition.

• Bore sighting at 25 yards allows for initial alignment of the scope with the bore.

• Using a target with an orange center helps in visualizing alignment through the bore.

New Section

In this section, the speaker demonstrates how to make adjustments on the scope based on bore sighting results.

Making Scope Adjustments

• After bore sighting, observe if there is any misalignment between crosshair and target center.

• Adjustments are needed to bring crosshair alignment closer to target center.

• Understanding click values is crucial for making precise adjustments. At 25 yards, click values need to be multiplied by four compared to 100 yards.

New Section

In this section, the speaker discusses an easier method using a lead sled and provides tips for counting clicks accurately.

Easier Method: Using a Lead Sled

• A lead sled helps in holding the rifle steady during adjustments.

• Align crosshair with target center as closely as possible before taking shots.

• Counting clicks accurately can be challenging, so using a lead sled and making final adjustments after the shot is recommended.

New Section

In this section, the speaker demonstrates how to make precise adjustments based on shot placement.

Making Precise Adjustments

• After taking a shot, observe where it hits in relation to the target center.

• If adjustments are needed, bring crosshair back to the original target center position.

• Rotate the turrets or use other adjustment mechanisms to move the crosshair precisely.

The transcript does not provide further sections or timestamps.

Adjusting for Parallax at 25 Yards

The speaker discusses the importance of adjusting for parallax when using a scope. At 25 yards, the parallax of the scope is set for perfect focus at 100 yards. Moving the head even slightly can cause a significant shift in aim.

Adjusting for Parallax

• When using a scope, be aware of parallax adjustment.

• At 25 yards, the parallax is set for perfect focus at 100 yards.

• Moving the head even slightly can result in a significant shift in aim.

Aligning Crosshair with Bullet Hole

The speaker demonstrates how to align the crosshair of the scope with a bullet hole on the target to ensure accuracy.

Aligning Crosshair

• Keep the rifle steady while turning the scope.

• Match up the crosshair with the bullet hole on the target.

• Ensure that both barrel and crosshair are looking at the same spot.

Fine-Tuning Alignment

The speaker continues to fine-tune alignment by making adjustments to ensure precise aiming.

Fine-Tuning Alignment

• Make adjustments by moving up and over.

• Aim to get as close as possible to perfect alignment between crosshair and bore.

• Being off by an inch at this point could result in being off by four inches at 100 yards.

Testing Accuracy at 100 Yards

The speaker prepares to test accuracy at 100 yards after aligning and fine-tuning alignment.

Testing Accuracy

• Set up target at 100 yards.

• Expect to be pretty close due to previous alignment steps.

• Use caution when shooting from this setup as it may not be comfortable or stable enough for accurate shooting.

Assessing Accuracy at 100 Yards

The speaker assesses the accuracy of the shot at 100 yards and discusses the impact of alignment on bullet placement.

Assessing Accuracy

• Bullet hits higher and to the left compared to the shot at 25 yards.

• Bullet placement mimics what was observed on the target at 25 yards.

• Despite slight deviation, still on paper and within an acceptable range.

Introduction to Patreon Support

The speaker takes a moment to introduce Patreon as a means of supporting their productions and expresses gratitude for both financial and moral support.

Supporting Through Patreon

• Viewers can support through Patreon.

• Financial and moral support is appreciated.

• Benefits include early access to videos, question answering, and consultations.

Demonstrating Dialing Reticle Over Bullet Hole

The speaker demonstrates how to dial the reticle over a bullet hole for precise aiming without moving the rifle.

Dialing Reticle Over Bullet Hole

• Ideal scenario: Have a buddy dial while you hold the rifle steady.

• Not comfortable using current setup for shooting at 100 yards.

• Demonstrates dialing process but will switch back to traditional tripod setup for shooting.

Adjusting Scope Settings for Precise Aiming

The speaker adjusts scope settings for precise aiming by dialing up and over to match bullet placement.

Adjusting Scope Settings

• Take initial shot with crosshair on bullseye.

• If shot hits off target, return rifle with same aim point on bullseye.

• Dial scope up or down based on vertical deviation from bullseye.

• Dial scope left or right based on horizontal deviation from bullseye.

Fine-Tuning Scope Adjustment

The speaker continues to fine-tune scope adjustment by bringing it over to the left for precise alignment.

Fine-Tuning Scope Adjustment

• Dial scope up or down to match vertical deviation.

• Dial scope left or right to match horizontal deviation.

• Aim to have the crosshair aligned with the bullet hole on the target.

Verifying Alignment and Accuracy

The speaker verifies alignment and accuracy after adjusting the scope settings.

Verifying Alignment and Accuracy

• If the gun didn't move, the bullet should hit where the barrel is pointed.

• Check if bullet placement matches intended aim point.

• Adjustments should result in improved accuracy and alignment.

New Section

In this section, the speaker discusses their excitement about the progress they have made in shooting and zeroing their rifle. They also mention the importance of considering barrel temperature when zeroing and hunting.

Zeroing Progress

• The speaker expresses excitement about having shot twice and almost zeroed their rifle.

• They mention planning their cards right for successful zeroing.

Barrel Temperature Considerations

• The speaker advises against using a hot barrel for zeroing, as it may not shoot as tightly as a cold barrel.

• They explain that a thin barrel like theirs is good for about three shots before it gets too hot and starts to wander.

• The speaker notes that heat causes expansion, which can affect accuracy.

New Section

In this section, the speaker continues discussing considerations when zeroing a rifle, including changes with new scopes and loose components. They also emphasize the importance of consistency in group shooting.

Changes with New Scope

• The speaker mentions that working with a new scope, mounts, and barrel can result in changes in shooting performance.

• They advise not getting too excited until after several rounds of consistent group shooting to allow everything to settle in.

Consistency in Group Shooting

• The speaker recommends doing a good bunch of group shooting to ensure consistency before finalizing the zero.

• They express encouragement based on initial results but acknowledge the need for further adjustments.

New Section

In this section, the speaker discusses their approach to determining the hunting zero and factors affecting accuracy. They also highlight the importance of trying different ammunition options.

Hunting Zero

• The speaker explains their preference for using the maximum point blank range system for hunting zeros.

• They aim to hit about two to two and a half inches above the point of aim, allowing for a maximum effective range.

Factors Affecting Accuracy

• The speaker mentions that even though their bullet holes are close to dead center, they won't have their final zero there.

• They attribute potential variations in accuracy to factors such as bullet velocity and ballistics efficiency.

Trying Different Ammunition

• The speaker advises trying different ammunition options to find the one that works best with the rifle.

• They suggest selecting a bullet suitable for the intended game and then finding the most accurate option.

New Section

In this section, the speaker concludes their discussion on zeroing and offers some final tips. They mention not taking the first shot at 100 yards without proper bore sighting and provide step-by-step instructions for zeroing.

Final Tips

• The speaker emphasizes not taking the first shot at 100 yards without collimated boresight or similar tools.

• They recommend removing the bolt from a bolt-action rifle, looking down at a red dot at 25 yards, and dialing everything up to be on target.

• After taking the first shot and noting its impact, they advise dialing the scope accordingly to achieve desired accuracy.

Conclusion

The transcript provides insights into zeroing a rifle, considering barrel temperature, consistency in group shooting, determining hunting zeros, factors affecting accuracy, trying different ammunition options, and step-by-step instructions for zeroing.